Time Delay Relay

Home > Circuits > Other > Time Delay Relay

Author	Views	Views Today	Rank	Comments
	559,119	1		88

A time delay relay is a relay that stays on for a certain amount of time once activated. This time delay relay is made up of a simple adjustable timer circuit which controls the actual relay. The time is adjustable from 0 to about 20 seconds with the parts specified. The current capacity of the circuit is only limited by what kind of relay you decide to use.

Schematic

Parts

Part	Total Qty.	Description	Substitutions
R1	1	1 Meg Pot
R2	1	10 K 1/4 Watt Resistor
C1	1	10uf 25V Electrolytic Capacitor
C2	1	0.01uf Ceramic Disc Capacitor
D1,D2	2	1N914 Diodes
U1	1	555 Timer IC
RELAY	1	9V Relay
S1	1	1A 120V SPST Switch
MISC	1	Board, Wire, Socket For U1

Notes

R1 adjusts the on time.

You can use a different capacitor for C1 to change the maximum on time.

S1 is used to activate the timing cycle. S1 can be replaced by a NPN transistor so that the circuit may be triggered by a computer, other circuit, etc.

Related Circuits

Comments

Add A Comment

Tara Chand timer ckt Friday, August 19, 2016 9:23:48 AM

i want a timer ckt which works 60 sec. in 2 hours and this is repeately. this ckt used in agriculture purpose, out the water from water tank only for 60 sec. and off.

Paco Time Delay Relay Wednesday, May 04, 2016 1:42:30 PM

Thanks Aaron for the original circuit and thanks to WillyAG for the little mod needed for my purposes.

pavan Time Delay Relay Monday, April 21, 2014 9:02:43 AM

If I want to use a 5v relay which parts of the circuit is to be changed. can the power supply can be reduced to 9v while using a relay of 5v. Expecting that I got an answer

Tony Time Delay Relay Saturday, February 08, 2014 5:54:21 PM

I need someone to make me a very small circuit that is on for 10seconds and off for 60 seconds and then it repeats over and over using a 3v cell battery

Steve W Time Delay Relay Tuesday, May 21, 2013 12:38:44 PM

This was EXACTLY what I needed to complete my project. Thank you so much for taking the time to post it.

ruel i want to supply it 24v and my relay is 24v but i wont operate Saturday, December 29, 2012 10:56:41 PM

i already get the cicuit in 12 volt,but my problem is i would like to increase my voltage into 24v so also increases my relay into 224v but wont work or oerate,pls help what to add components or change?i want 24v dc to run my motor

Billy Time Delay Relay Thursday, December 13, 2012 1:29:45 AM

If I use 9V as my input power supply,,,, do I have to change anything else??? And,,, I am not going out to a relay,,, I am going directly to an E-Match,,, to trigger an ejection charge in a model rocket.... But I do want all the power I can get,,, to make sure the charge ignites.. Thanks...

mok Time Delay Relay Sunday, April 29, 2012 11:48:40 PM

I'm looking to adjust the time of the delay for 1week. How do I calculate the change required to the capacitor? i want to know more about delay...

Indrajit Biswas Time Delay Relay Tuesday, February 28, 2012 9:21:09 AM

Thanks for the circuit diagram. Last some days I was searching the same, which I want to used. I hope it will help to me.

Chris Stewart Time Delay Relay Saturday, January 21, 2012 6:37:01 PM

Aaron, I have know you through the RX-7 world for years. But when I go to search for a time delay relay to build one, your site comes up second on Google. Mind blowing. Water level low>water valve opened (heating system)

The last 10 comments are currently shown. Show All Comments. Add A Comment

If you would like to leave a comment, you can do so using the form below. Comments can be things like suggestions, successes or failures, improvements, similar circuits, error reports, an answer to a previous commenter's question, or anything in between. However if you would like to ask a question it is suggested that you use the forum instead. The forum provides a more robust environment for discussion.

Important: If you post a technical question here, there is no guarantee it will be answered. All technical questions should be posted to the forum. The owner of this site generally does not answer questions in comments.

All comments are subject to approval before they are displayed here, so your comment will not appear immediately. This is done mainly to prevent spam and other abuse. If you wish to remain anonymous, simply enter "anonymous" for your name and/or email.

Name:
Email:
Subject:
Comments:
Anti Spam Code:	Please enter the exact text shown in the image above into the box below. Browser cookies must be enabled to comment on circuits.

Privacy Policy

Tara Chand	timer ckt	Friday, August 19, 2016 9:23:48 AM
i want a timer ckt which works 60 sec. in 2 hours and this is repeately. this ckt used in agriculture purpose, out the water from water tank only for 60 sec. and off.
Paco	Time Delay Relay	Wednesday, May 04, 2016 1:42:30 PM
Thanks Aaron for the original circuit and thanks to WillyAG for the little mod needed for my purposes.
pavan	Time Delay Relay	Monday, April 21, 2014 9:02:43 AM
If I want to use a 5v relay which parts of the circuit is to be changed. can the power supply can be reduced to 9v while using a relay of 5v. Expecting that I got an answer
Tony	Time Delay Relay	Saturday, February 08, 2014 5:54:21 PM
I need someone to make me a very small circuit that is on for 10seconds and off for 60 seconds and then it repeats over and over using a 3v cell battery
Steve W	Time Delay Relay	Tuesday, May 21, 2013 12:38:44 PM
This was EXACTLY what I needed to complete my project. Thank you so much for taking the time to post it.
ruel	i want to supply it 24v and my relay is 24v but i wont operate	Saturday, December 29, 2012 10:56:41 PM
i already get the cicuit in 12 volt,but my problem is i would like to increase my voltage into 24v so also increases my relay into 224v but wont work or oerate,pls help what to add components or change?i want 24v dc to run my motor
Billy	Time Delay Relay	Thursday, December 13, 2012 1:29:45 AM
If I use 9V as my input power supply,,,, do I have to change anything else??? And,,, I am not going out to a relay,,, I am going directly to an E-Match,,, to trigger an ejection charge in a model rocket.... But I do want all the power I can get,,, to make sure the charge ignites.. Thanks...
mok	Time Delay Relay	Sunday, April 29, 2012 11:48:40 PM
I'm looking to adjust the time of the delay for 1week. How do I calculate the change required to the capacitor? i want to know more about delay...
Indrajit Biswas	Time Delay Relay	Tuesday, February 28, 2012 9:21:09 AM
Thanks for the circuit diagram. Last some days I was searching the same, which I want to used. I hope it will help to me.
Chris Stewart	Time Delay Relay	Saturday, January 21, 2012 6:37:01 PM
Aaron, I have know you through the RX-7 world for years. But when I go to search for a time delay relay to build one, your site comes up second on Google. Mind blowing. Water level low>water valve opened (heating system)