Water Detector With Sump/Bilge Pump Controller

Author	Views	Views Today	Rank	Comments
	41,290	60		16

This moisture detector with pump controller is built around the special purpose LM1830 IC. The LM1830 is designed to detect moisture by passing an AC current through a set of probes. An internal comparator compares the resistance of the probes to an internal reference. When the resistance between the probes is low (indicating the presence of water or other conductive liquid) then the IC triggers it's output. An AC signal avoids electroplating and corrosion problems that are common when DC is used. To provide an adjustable delay hysteresis to avoid cycling the pump, a timer based around the 555 is used a range of about 5 seconds to two minutes. In this way the pump will stay active for a set amount of time even if the fluid level is below that of the probes.

Schematic

Scheamtic of the water detector with pump controller

Parts

Part	Total Qty.	Description	Substitutions
R1	1	470 Ohm 1/4 W Resistor
R2, R4	1	10K 1/4 W Resistor
R3	1	6.8K 1/4 W Resistor
R5	1	1 Meg Linear Taper Pot
R6	1	51K 1/4 W Resistor
C1	1	470uF 35V Electrolytic Capacitor
C2	1	0.001uF Ceramic Disc Capacitor
C3	1	0.05 uF Ceramic Disc Capacitor
C4	1	20uF 35V Electrolytic Capacitor
C5	1	6.8uF 35V Electrolytic Capacitor
C6, C8	2	0.01uF Ceramic Disc Capacitor
C7	1	100uF 35V Electrolytic Capacitor
U1	1	LM1830 Fluid Detection IC
U2	1	555 Timer
Q1	1	2N5305 NPN Power Transistor
D1, D2	2	1N4148 Signal Diode
D3	1	1N4002 Rectifier Diode
K1	1	Relay With 12V Coil (See Notes)
S1	1	SPST Switch
PROBES	1	Stainless Steel Probes (See Notes)
MISC	1	Case, Knob, Board, Wire, Sockets For U1 and U2

Notes

The probes should be made of stainless steel and mounted in a non-conductive fixture. Stainless steel nails, bolts or welding rod will make ideal probes. Good non-conductive materials are Lexan, plexiglass or plastic. The probes are to be placed at the liquid level at which you wish the pump to turn on.

K1 should be chosen according to the requirements of the pump. If you are running a 12V pump then common automotive relays will work fine. If you are running a mains powered pump then you will need to make sure the contacts are rated accordingly.

S1 provides a manual pump switch.

R5 adjusts the on-time of the pump once moisture has been detected. It is adjustable from approximately 5 seconds to approximately 2 minutes.

The probes should be cleaned periodically to assure reliable operation.

Related Circuits

Comments

Add A Comment

Zulaz Water Detector With Sump/Bilge Pump Controller Tuesday, September 01, 2009 2:46:21 AM

hi there..i choose this circuit as my project..can i use AC pump instead of using 12Vdc pump and replace 1 meg linear taper pot into 1 meg log taper pot.. is it ok? thnx ..pls reply

rvp Water Detector With Sump/Bilge Pump Controller Saturday, May 23, 2009 1:46:51 AM

Why do you put a 470 ohm res. at Pin 14 that is +Vcc. The mfgr cites +16V operating voltage and direct connect to Vcc.

Philippe Tremblay Water Detector With Sump/Bilge Pump Controller Friday, October 17, 2008 12:53:15 PM

This circuit works very well !!! I used it to start a sub-pump in the basement in case of water distribution malfunction. Easy, inexpensive and secure !!!! Thanks !!!!

lavender Water Detector With Sump/Bilge Pump Controller Wednesday, October 08, 2008 9:41:34 AM

i want to combine this water detector with sump/bilge pump controller with bluetooth.thats means i want to connect in handphone that it will detect the water.can u give an idea?

karanjah Water Detector With Sump/Bilge Pump Controller Wednesday, September 10, 2008 1:58:31 AM

i would like to construct an operational one that includes a level sensor, analogue to digital & digital to analogue interfacing circuit & an operational monitoring software.

nilesh kashid Water Detector With Sump/Bilge Pump Controller Saturday, September 06, 2008 1:16:17 AM

its a interesting circuit!!! will u give me the details about IC1830 equivalent?

Trev Water Detector With Sump/Bilge Pump Controller Wednesday, May 21, 2008 5:17:00 AM

Is there a replacement for the LM1830? i cannot source one in England.

Anonymous Water Detector With Sump/Bilge Pump Controller Sunday, May 04, 2008 5:10:10 AM

Just like chris I need a circuit for refilling a tank. Could you please send me the circuit or instructions on how to modify this one to do it. I know how to make a detector and refill for a single probe. But it wouldn't do much good because it would need a few seconds after the initial low point to get the fluid back up to a suitable level. If anyone knows how could please email me.

anonymous Water Detector With Sump/Bilge Pump Controller Tuesday, April 01, 2008 3:08:17 PM

i have to make a working model for water level indicator n controller. so can u plz send me some more details about this circuit.

chris Water Detector With Sump/Bilge Pump Controller Monday, March 03, 2008 3:45:45 PM

hi we are doing a water conservatin progect at school and are building a model we need a circuit for filling a tank so a pump is turned on and refilles the tank when water is running low we have a 240vac pump (were in the uk) and your circuit looks extremely practical can you send me any extended details if you have them thanks chris

Billous Water Detector With Sump/Bilge Pump Controller Sunday, February 17, 2008 4:38:10 PM

Why do you put a 470 ohm res. at Pin 14 that is +Vcc. The mfgr cites +16V operating voltage and direct connect to Vcc. Where can this be purchased... Mouser and Digikey don't have it in stock.

irshad Water Detector With Sump/Bilge Pump Controller Saturday, February 16, 2008 10:42:33 AM

when the u2 ic will get activated and how the relay is switched on , you have given 12v dc via a s1 to the coil of the relay and o/p of u2 is connected via a diode d2 . please explain how it works.

anonymous Water Detector With Sump/Bilge Pump Controller Friday, January 25, 2008 10:25:03 PM

is this working??

Colleen Water Detector With Sump/Bilge Pump Controller Monday, January 21, 2008 10:20:25 PM

This looks like a very useful circuit. I am working on a robot and trying to implement this circuit in order to detect water "moisture" and send a wireless output. Do you have any ideas on how to add an alarm to this system once moisture has been detected? Also, do you think a sufficient amount of H20 has to be present?...or is condensed steam enough?? Thank you thank you so much for the info!! <3 XO Colleen

revannath Water Detector With Sump/Bilge Pump Controller Monday, January 07, 2008 4:26:10 AM

sir can you provide information about,how to detect water in earth or in ground?can it is detect by using earth resistance testar?please publish this information.

thiru Water Detector With Sump/Bilge Pump Controller Tuesday, December 04, 2007 7:40:01 AM

its not fully automatic....

All comments are being shown. Show Only Last 10 Comments. Add A Comment

If you would like to leave a comment, you can do so using the form below. Comments can be things like suggestions, successes or failures, improvements, similar circuits, error reports, an answer to a previous commenter's question, or anything in between. However if you would like to ask a question it is suggested that you use the forum instead. The forum provides a more robust environment for discussion.

Important: If you post a technical question here, there is no guarantee it will be answered. All technical questions should be posted to the forum. The owner of this site generally does not answer questions in comments.

All comments are subject to approval before they are displayed here, so your comment will not appear immediately. This is done mainly to prevent spam and other abuse. If you wish to remain anonymous, simply enter "anonymous" for your name and/or email.

Name:
Email:
Subject:
Comments:
Anti Spam Code:	Please enter the exact text shown in the image above into the box below. Browser cookies must be enabled to comment on circuits.

Privacy Policy

Zulaz	Water Detector With Sump/Bilge Pump Controller	Tuesday, September 01, 2009 2:46:21 AM
hi there..i choose this circuit as my project..can i use AC pump instead of using 12Vdc pump and replace 1 meg linear taper pot into 1 meg log taper pot.. is it ok? thnx ..pls reply
rvp	Water Detector With Sump/Bilge Pump Controller	Saturday, May 23, 2009 1:46:51 AM
Why do you put a 470 ohm res. at Pin 14 that is +Vcc. The mfgr cites +16V operating voltage and direct connect to Vcc.
Philippe Tremblay	Water Detector With Sump/Bilge Pump Controller	Friday, October 17, 2008 12:53:15 PM
This circuit works very well !!! I used it to start a sub-pump in the basement in case of water distribution malfunction. Easy, inexpensive and secure !!!! Thanks !!!!
lavender	Water Detector With Sump/Bilge Pump Controller	Wednesday, October 08, 2008 9:41:34 AM
i want to combine this water detector with sump/bilge pump controller with bluetooth.thats means i want to connect in handphone that it will detect the water.can u give an idea?
karanjah	Water Detector With Sump/Bilge Pump Controller	Wednesday, September 10, 2008 1:58:31 AM
i would like to construct an operational one that includes a level sensor, analogue to digital & digital to analogue interfacing circuit & an operational monitoring software.
nilesh kashid	Water Detector With Sump/Bilge Pump Controller	Saturday, September 06, 2008 1:16:17 AM
its a interesting circuit!!! will u give me the details about IC1830 equivalent?
Trev	Water Detector With Sump/Bilge Pump Controller	Wednesday, May 21, 2008 5:17:00 AM
Is there a replacement for the LM1830? i cannot source one in England.
Anonymous	Water Detector With Sump/Bilge Pump Controller	Sunday, May 04, 2008 5:10:10 AM
Just like chris I need a circuit for refilling a tank. Could you please send me the circuit or instructions on how to modify this one to do it. I know how to make a detector and refill for a single probe. But it wouldn't do much good because it would need a few seconds after the initial low point to get the fluid back up to a suitable level. If anyone knows how could please email me.
anonymous	Water Detector With Sump/Bilge Pump Controller	Tuesday, April 01, 2008 3:08:17 PM
i have to make a working model for water level indicator n controller. so can u plz send me some more details about this circuit.
chris	Water Detector With Sump/Bilge Pump Controller	Monday, March 03, 2008 3:45:45 PM
hi we are doing a water conservatin progect at school and are building a model we need a circuit for filling a tank so a pump is turned on and refilles the tank when water is running low we have a 240vac pump (were in the uk) and your circuit looks extremely practical can you send me any extended details if you have them thanks chris
Billous	Water Detector With Sump/Bilge Pump Controller	Sunday, February 17, 2008 4:38:10 PM
Why do you put a 470 ohm res. at Pin 14 that is +Vcc. The mfgr cites +16V operating voltage and direct connect to Vcc. Where can this be purchased... Mouser and Digikey don't have it in stock.
irshad	Water Detector With Sump/Bilge Pump Controller	Saturday, February 16, 2008 10:42:33 AM
when the u2 ic will get activated and how the relay is switched on , you have given 12v dc via a s1 to the coil of the relay and o/p of u2 is connected via a diode d2 . please explain how it works.
anonymous	Water Detector With Sump/Bilge Pump Controller	Friday, January 25, 2008 10:25:03 PM
is this working??
Colleen	Water Detector With Sump/Bilge Pump Controller	Monday, January 21, 2008 10:20:25 PM
This looks like a very useful circuit. I am working on a robot and trying to implement this circuit in order to detect water "moisture" and send a wireless output. Do you have any ideas on how to add an alarm to this system once moisture has been detected? Also, do you think a sufficient amount of H20 has to be present?...or is condensed steam enough?? Thank you thank you so much for the info!! <3 XO Colleen
revannath	Water Detector With Sump/Bilge Pump Controller	Monday, January 07, 2008 4:26:10 AM
sir can you provide information about,how to detect water in earth or in ground?can it is detect by using earth resistance testar?please publish this information.
thiru	Water Detector With Sump/Bilge Pump Controller	Tuesday, December 04, 2007 7:40:01 AM
its not fully automatic....