Phone Busy Indicator

Home > Circuits > Telephone > Phone Busy Indicator

Author	Views	Views Today	Rank	Comments
	216,551	2		24

Have you ever been using the modem or fax and someone else picks up the phone, breaking the connection? Well, this simple circuit should put an end to that. It signals that the phone is in use by lighting a red LED. When the phone is not in use, a green LED is lit. It needs no external power and can be connected anywhere on the phone line, even mounted inside the phone.

Schematic

Parts

Part	Total Qty.	Description	Substitutions
R1	1	3.3K 1/4 W Resistor
R2	1	33K 1/4 W Resistor
R3	1	56K 1/4 W Resistor
R4	1	22K 1/4 W Resistor
R5	1	4.7K 1/4 W Resistor
Q1, Q2	2	2N3392 NPN Transistor
BR1	1	1.5 Amp 250 PIV Bridge Rectifier
LED1	1	Red LED
LED2	1	Green LED
MISC	1	Wire, Case, Phone Cord

Notes

This is a very simple circuit and is easily made on a perf board and mounted inside the phone.

LED1 and LED2 flash on and off while the phone is ringing.

Do not worry about mixing up the Tip and Ring connections.

The ring voltage on a phone line is anywhere from 90 to 130 volts. Make sure no one calls while you are making the line connections or you'll know it. :-)

In some countries or states you will have to ask the phone company before you connect this to the line. It might even require an inspection.

If the circuit causes distortion on the phone line, connect a 680 ohm resistor in between one of the incoming line wires and the bridge rectifier.

Related Circuits

Comments

Add A Comment

aisha Phone Busy Indicator Friday, August 15, 2014 2:24:38 AM

plz send me the complete discription and how can i make this circuit.... some one saying in comments "that this circuit didn't work, but after some minor adjustments, it did seem to work just fine. Nice circuit." so plz tell me whats the minor adjusment u done???? plz give me reply as soon as possoble

Fonseka Phone Busy Indicator Sunday, May 18, 2014 12:25:39 AM

i like this cct.that's function as wel. but i want to cct of how to indicated exchange output line correctivity .i know that's very difficult . can you try to drow in cct next send it for me.

PEter D Phone Busy Indicator Friday, February 24, 2012 4:33:42 PM

I am simulating this circuit in LTSpice, and it does not work. The LED drop voltages are not what they are supposed to be. As one comment here says, both LED's are on at the same time. Simulate the circuit with LTSpice and find out that the circuit is bad. Plus, LTSpice shows that circuit draws 2.25 mA when telephone is not in use! This is colossal current! You will have telephone companies contact you thinking that you use power for free for non-telephone needs (lighting, etc). Do simulation before buying and building. Simulation took me only about 1 hr to create.

anonymouslhb Phone Busy Indicator Monday, October 18, 2010 5:30:19 PM

WARNING ! Modern phone lines require a load resistance of ten megohms. The older relay systems would work fine . Your phone will indicate "busy" at all times. You cannot put any load on a new system in the of-line condition. You will have to use a wall-wart transformer to power any of-line system. 10 meg ohms impeadence required to be off line. Basicly , try it , you will find out. .. LHB.

zain Phone Busy Indicator Thursday, March 25, 2010 3:43:41 PM

plz send me the complete discription and how can i make this circuit.... some one saying in comments "that this circuit didn't work, but after some minor adjustments, it did seem to work just fine. Nice circuit." so plz tell me whats the minor adjusment u done???? plz give me reply as soon as possoble

adam Phone Busy Indicator Wednesday, April 01, 2009 12:52:00 PM

I originally posted that this circuit didn't work, but after some minor adjustments, it did seem to work just fine. Nice circuit.

anonymous Phone Busy Indicator Saturday, March 21, 2009 2:09:53 AM

Hi, I have been trying your project but it doesn't seem to be working for me. Mine just has both LED's Stay on constantly. Do different phone providers affect this, or possiby newer phones? Also I did switch the 1.5 Amp 250 PIV Bridge Rectifier because I could not find it with a 1.5 Amp 400 Volt Bridge Rectifier. I dont think this will make a difference but if it does please let me know. Do you know where I could find a 1.5 Amp 250 PIV Bridge Rectifier? Thanks

Germ Phone Busy Indicator Tuesday, March 10, 2009 10:20:54 PM

I have tested that circuit and it works great. LED are dim. use 2N3904 or 2N2222 The only problem I had is that I did not have the right diode for my bridge rectifer. 1N4148 did not work. I then use four 1N4001. It did work, the LED light up nicelly but you could not call!! I measure the voltage and got 48V. I live in Canada. The damn circuit is voltage divider! Do you homework, we will not do it for you. Stop asking questions and build it! It will cost you 1$ in parts!

acme fixer Phone Busy Indicator Tuesday, March 10, 2009 12:29:09 PM

This circuit may work well, but it draws too much current from the phone line when it is idle, causing the central office to think that there is leakage on the line. I strongly advise you to not use it, instead use the one at Bowden's hobby circuits (google for it). Bowden's draws much, much less current when idle.

prince Phone Busy Indicator Wednesday, February 11, 2009 12:51:21 PM

tell me that how i make the major project with combine this project to the other like that ringer, busy indicator and more in telephones. and plz tell me the combined circuit to make the major project and inform me about the components used

arunkaul Phone Busy Indicator Monday, July 28, 2008 2:49:12 AM

i want ot know the complete description of parts and working of Phone Busy Indicator.also i want assurance that when implemented on pcb it works well..tells us about another ic no of npn taransistor because the spicpied one is not available if phone busy indicator work on them then tell us....Hi! im jake. can u help me with my project. How can i determine if i call then the receiver is answer the call? waitng for reply..... WANT TO KNOW HOW THIS CIRCUIT IS WORKING IN DETAIL ,ITS APPLICATION...plz do mail me all decriptions n details widin two days to mine mail id

rehan Phone Busy Indicator Thursday, May 29, 2008 1:16:34 PM

i want ot know the complete description of parts and working of Phone Busy Indicator.also i want assurance that when implemented on pcb it works well.

manzoor ali Phone Busy Indicator Saturday, May 24, 2008 1:39:51 AM

tells us about another ic no of npn taransistor because the spicpied one is not available if phone busy indicator work on them then tell us.

PATRICK GERARD Phone Busy Indicator Tuesday, May 13, 2008 9:40:06 AM

think you

anonymous Phone Busy Indicator Sunday, February 10, 2008 7:48:30 PM

I assembled this circuit and it works really great, now I can tell when somebody has the phone extension in use. Building it was really cheap and easy. Other circuits i saw were more complex and required external power. Thanks to the author for that nice piece of work

ashiya Phone Busy Indicator Wednesday, January 30, 2008 10:21:26 AM

i need a full description in this..thanks..

Jake Cyrill Babao Phone Busy Indicator Saturday, November 17, 2007 1:00:56 AM

Hi! im jake. can u help me with my project. How can i determine if i call then the receiver is answer the call? waitng for reply.

saroj Phone Busy Indicator Wednesday, September 05, 2007 5:16:46 AM

i want to know about the working of phone busy indicator in detail and it's applications.

sumir Phone Busy Indicator Monday, April 30, 2007 3:09:44 AM

I WANT TO KNOW HOW THIS CIRCUIT IS WORKING IN DETAIL ,ITS APPLICATION........PLEASE VERY FAST IN 5 HOURS

Mayer Phone Busy Indicator Monday, April 16, 2007 4:32:45 PM

Hello you, I just looked your phone busy indicator cct and I would like to know how can I add a PIC 12C508A to fit within ? I only want to make my PIC 12C508A program started if line is not in use. a) Should I connect one of the PIC pin instead of led 1 ? b) I don't need led2 (should I only remove the led? should R2/3/4/5 values be changed ? Tks for answering the newbies that I'am : ) Tks/Carl

Jean Maragno Phone Busy Indicator Thursday, April 12, 2007 8:26:22 PM

VERY GOOD !

TANUI G.K. Phone Busy Indicator Wednesday, April 11, 2007 8:08:54 AM

i will like to know more about-Circuit design -circuit operation and its applications

TANUI G.K. Phone Busy Indicator Wednesday, April 11, 2007 7:55:59 AM

circuit design procedure circuit operation

Larry Phone Busy Indicator Saturday, March 10, 2007 8:30:04 PM

What voltage should the LED's be? Thank you

All comments are being shown. Show Only Last 10 Comments. Add A Comment

If you would like to leave a comment, you can do so using the form below. Comments can be things like suggestions, successes or failures, improvements, similar circuits, error reports, an answer to a previous commenter's question, or anything in between. However if you would like to ask a question it is suggested that you use the forum instead. The forum provides a more robust environment for discussion.

Important: If you post a technical question here, there is no guarantee it will be answered. All technical questions should be posted to the forum. The owner of this site generally does not answer questions in comments.

All comments are subject to approval before they are displayed here, so your comment will not appear immediately. This is done mainly to prevent spam and other abuse. If you wish to remain anonymous, simply enter "anonymous" for your name and/or email.

Name:
Email:
Subject:
Comments:
Anti Spam Code:	Please enter the exact text shown in the image above into the box below. Browser cookies must be enabled to comment on circuits.

Privacy Policy

aisha	Phone Busy Indicator	Friday, August 15, 2014 2:24:38 AM
plz send me the complete discription and how can i make this circuit.... some one saying in comments "that this circuit didn't work, but after some minor adjustments, it did seem to work just fine. Nice circuit." so plz tell me whats the minor adjusment u done???? plz give me reply as soon as possoble
Fonseka	Phone Busy Indicator	Sunday, May 18, 2014 12:25:39 AM
i like this cct.that's function as wel. but i want to cct of how to indicated exchange output line correctivity .i know that's very difficult . can you try to drow in cct next send it for me.
PEter D	Phone Busy Indicator	Friday, February 24, 2012 4:33:42 PM
I am simulating this circuit in LTSpice, and it does not work. The LED drop voltages are not what they are supposed to be. As one comment here says, both LED's are on at the same time. Simulate the circuit with LTSpice and find out that the circuit is bad. Plus, LTSpice shows that circuit draws 2.25 mA when telephone is not in use! This is colossal current! You will have telephone companies contact you thinking that you use power for free for non-telephone needs (lighting, etc). Do simulation before buying and building. Simulation took me only about 1 hr to create.
anonymouslhb	Phone Busy Indicator	Monday, October 18, 2010 5:30:19 PM
WARNING ! Modern phone lines require a load resistance of ten megohms. The older relay systems would work fine . Your phone will indicate "busy" at all times. You cannot put any load on a new system in the of-line condition. You will have to use a wall-wart transformer to power any of-line system. 10 meg ohms impeadence required to be off line. Basicly , try it , you will find out. .. LHB.
zain	Phone Busy Indicator	Thursday, March 25, 2010 3:43:41 PM
plz send me the complete discription and how can i make this circuit.... some one saying in comments "that this circuit didn't work, but after some minor adjustments, it did seem to work just fine. Nice circuit." so plz tell me whats the minor adjusment u done???? plz give me reply as soon as possoble
adam	Phone Busy Indicator	Wednesday, April 01, 2009 12:52:00 PM
I originally posted that this circuit didn't work, but after some minor adjustments, it did seem to work just fine. Nice circuit.
anonymous	Phone Busy Indicator	Saturday, March 21, 2009 2:09:53 AM
Hi, I have been trying your project but it doesn't seem to be working for me. Mine just has both LED's Stay on constantly. Do different phone providers affect this, or possiby newer phones? Also I did switch the 1.5 Amp 250 PIV Bridge Rectifier because I could not find it with a 1.5 Amp 400 Volt Bridge Rectifier. I dont think this will make a difference but if it does please let me know. Do you know where I could find a 1.5 Amp 250 PIV Bridge Rectifier? Thanks
Germ	Phone Busy Indicator	Tuesday, March 10, 2009 10:20:54 PM
I have tested that circuit and it works great. LED are dim. use 2N3904 or 2N2222 The only problem I had is that I did not have the right diode for my bridge rectifer. 1N4148 did not work. I then use four 1N4001. It did work, the LED light up nicelly but you could not call!! I measure the voltage and got 48V. I live in Canada. The damn circuit is voltage divider! Do you homework, we will not do it for you. Stop asking questions and build it! It will cost you 1$ in parts!
acme fixer	Phone Busy Indicator	Tuesday, March 10, 2009 12:29:09 PM
This circuit may work well, but it draws too much current from the phone line when it is idle, causing the central office to think that there is leakage on the line. I strongly advise you to not use it, instead use the one at Bowden's hobby circuits (google for it). Bowden's draws much, much less current when idle.
prince	Phone Busy Indicator	Wednesday, February 11, 2009 12:51:21 PM
tell me that how i make the major project with combine this project to the other like that ringer, busy indicator and more in telephones. and plz tell me the combined circuit to make the major project and inform me about the components used
arunkaul	Phone Busy Indicator	Monday, July 28, 2008 2:49:12 AM
i want ot know the complete description of parts and working of Phone Busy Indicator.also i want assurance that when implemented on pcb it works well..tells us about another ic no of npn taransistor because the spicpied one is not available if phone busy indicator work on them then tell us....Hi! im jake. can u help me with my project. How can i determine if i call then the receiver is answer the call? waitng for reply..... WANT TO KNOW HOW THIS CIRCUIT IS WORKING IN DETAIL ,ITS APPLICATION...plz do mail me all decriptions n details widin two days to mine mail id
rehan	Phone Busy Indicator	Thursday, May 29, 2008 1:16:34 PM
i want ot know the complete description of parts and working of Phone Busy Indicator.also i want assurance that when implemented on pcb it works well.
manzoor ali	Phone Busy Indicator	Saturday, May 24, 2008 1:39:51 AM
tells us about another ic no of npn taransistor because the spicpied one is not available if phone busy indicator work on them then tell us.
PATRICK GERARD	Phone Busy Indicator	Tuesday, May 13, 2008 9:40:06 AM
think you
anonymous	Phone Busy Indicator	Sunday, February 10, 2008 7:48:30 PM
I assembled this circuit and it works really great, now I can tell when somebody has the phone extension in use. Building it was really cheap and easy. Other circuits i saw were more complex and required external power. Thanks to the author for that nice piece of work
ashiya	Phone Busy Indicator	Wednesday, January 30, 2008 10:21:26 AM
i need a full description in this..thanks..
Jake Cyrill Babao	Phone Busy Indicator	Saturday, November 17, 2007 1:00:56 AM
Hi! im jake. can u help me with my project. How can i determine if i call then the receiver is answer the call? waitng for reply.
saroj	Phone Busy Indicator	Wednesday, September 05, 2007 5:16:46 AM
i want to know about the working of phone busy indicator in detail and it's applications.
sumir	Phone Busy Indicator	Monday, April 30, 2007 3:09:44 AM
I WANT TO KNOW HOW THIS CIRCUIT IS WORKING IN DETAIL ,ITS APPLICATION........PLEASE VERY FAST IN 5 HOURS
Mayer	Phone Busy Indicator	Monday, April 16, 2007 4:32:45 PM
Hello you, I just looked your phone busy indicator cct and I would like to know how can I add a PIC 12C508A to fit within ? I only want to make my PIC 12C508A program started if line is not in use. a) Should I connect one of the PIC pin instead of led 1 ? b) I don't need led2 (should I only remove the led? should R2/3/4/5 values be changed ? Tks for answering the newbies that I'am : ) Tks/Carl
Jean Maragno	Phone Busy Indicator	Thursday, April 12, 2007 8:26:22 PM
VERY GOOD !
TANUI G.K.	Phone Busy Indicator	Wednesday, April 11, 2007 8:08:54 AM
i will like to know more about-Circuit design -circuit operation and its applications
TANUI G.K.	Phone Busy Indicator	Wednesday, April 11, 2007 7:55:59 AM
circuit design procedure circuit operation
Larry	Phone Busy Indicator	Saturday, March 10, 2007 8:30:04 PM
What voltage should the LED's be? Thank you