Solid State Tesla Coil Circuit

Home > Circuits > Power Supply > Solid State Tesla Coil

Search:

Author	Views	Views Today	Rank	Comments
	150,040	2		4

Schematic

Parts

Part Total Qty. Description Substitutions R1, R5, R9 3 180 Ohm 1/4W Resistor R2 1 10K Pot R3, R7 2 10 Ohm 1/4W Resistor R4 1 5K Pot R6 1 7.5K 1/4W Resistor R8 1 150 Ohm 1/4W Resistor R10 1 1 Ohm 5W Resistor C1 1 0.0047uF 50V Polyester Capacitor C2 1 0.05uF 50V Polyester Capacitor C3 1 220uF 25V Electrolytic Capacitor C4 1 0.01uF 1200V Polyester Capacitor Q1, Q2 2 2N2222 NPN Transistor 2N3904 Q3 1 SSM5N55 MOSFET U1 1 555 Timer Integrated Circuit U2 1 LM7809 9V Linear Regulator L1 1 100uH Choke Coil T1 1 Penn-Tran 1-017-5372 Flyback Transformer See Notes MISC 1 Board, Wire, Case, Socket for U1, Heatsink For Q3, Output Terminal (See Notes)

Notes

1. T1 as specified in the parts list is going to be almost impossible to find, but don't worry. Penn-Tran was bought by Wiltron and no longer exists. However, most any medium to large flyback transformer will work as long as it does not have an internal rectifier. Suitable units are most often found in TVs made during the 1970s and 1980s. Look for the most impressive, dangerous, menacing transformer you can find. If you need an idea, a picture of a great transformer for use in this circuit:

   

   These can be found in a small metal box generally in the corner of the TV case, complete with a very handy voltage multiplier unit and usually a nice heatsink.

   You will need to either look up the datasheet for the transformer you have, or probe it with an ohmmeter to identify the coil connections. Most flybacks have a load of taps on the HV side to provide focusing, horizontal and vertical signals. These taps are generally of no use to you. To find the primary (coil B-A on the schematic) you need to find the two lowest resistance connections that are not also connected to the HV secondary wiring. Alternately, if your flyback has an open frame like the one in the picture, you can wind on 5 or so turns of 16 gauge magnet wire as a primary. You will need to experiment with the number of turns to get maximum output. The HV ground lead (connection C on the schematic) is generally easy to locate. It will come from the HV secondary and be tied to the frame of the transformer or chassis ground.

   If by some miracle you were able to locate the Penn-Tran transformer, then connection B is the red dot on the transformer, A corresponds to the black dot, and C matches the orange dot.

2. If the TV you salvaged the transformer from has a voltage multiplier unit (visible slightly at the far right of the above picture), then take it as well. It can multiply the output of this circuit into very high (over 100KV) DC voltages.
3. When building the circuit, leave the flyback disconnected. Connect a 10 Ohm 10W resistor in place of the primary of T1 and connect a scope to the collector of Q3. Adjust R4 to produce an off time of about 10 microseconds. Adjust R2 for an on time of about 70 microseconds. Now remove the scope, 10 ohm resistor, and connect up T1. Power the circuit back on and you should have a high voltage available at the output. If you do not have a scope, just set both pots in their middle position and then adjust them by trail and error until you get the biggest spark at the output of T1.
4. Q3 will require a heatsink.
5. Needless to say, this circuit can produce dangerous voltage. At the very least you are looking at a painful shock. More then likely a decent burn will result from contact with the HV output, as well as instant and uncontrollable muscle contraction. If you have heart problems, don't build this circuit. Be careful!.

If you would like to leave a comment, you can do so using the form below. Comments can be things like suggestions, successes or failures, improvements, similar circuits, error reports, an answer to a previous commenter's question, or anything in between. However if you would like to ask a question it is suggested that you use the forum instead. The forum provides a more robust environment for discussion.

Important: If you post a technical question here, there is no guarantee it will be answered. All technical questions should be posted to the forum. The owner of this site generally does not answer questions in comments.

All comments are subject to approval before they are displayed here, so your comment will not appear immediately. This is done mainly to prevent spam and other abuse. If you wish to remain anonymous, simply enter "anonymous" for your name and/or email.

Name:
Email:
Subject:
Comments:
Anti Spam Code:	Please enter the exact text shown in the image above into the box below. Browser cookies must be enabled to comment on circuits.
Privacy Policy

Back To Circuits Page | Mail Me | Search |