Voltage Inverter II


Home > Circuits > Power Supply > Voltage Inverter II Buy Me A Coffee
Author Views Views Today Rank Comments
206,914 5 19
This simple and inexpensive circuit can produce a dual (positive and negative) voltage from a single supply input. It is therefore extremely useful for powering opamp and other circuits that require a dual voltage from a single battery. The circuit will operate at an input voltage from around 5V to 20V and produce a output from +-2.5V to +-10V.

Schematic

This is the schematic of the Voltage Inverter

Parts

Part
Total Qty.
Description
Substitutions
R111M Linear Pot
C1,C2215uf 25V Electrolytic Capacitor
U11LM380 Audio Amp Chip
MISC1Heatsink For U1, Binding Posts (For Input/Output), Wire, Board

Notes

  1. U1 dissipates around 1W and will therefore require a heatsink.
  2. R1 is used to equalize the outputs. The first time you use the circuit, it should be set to mid range and then adjusted with the aid of a voltmeter. Measure each output while adjusting. The circuit is calibrated when both outputs read the same voltage (either positive or negative).

Related Circuits

6V to 12V Converter, Portable CD Player Adapter For Car, Car Battery Charger, Automatic 12V Lead Acid Battery Charger, Solid State Tesla Coil/High Voltage Generator, 12VDC To 120VAC Inverter, LASER Power Supply, Power Supply, High Current Power Supply, Dual Polarity Power Supply, High Voltage High Current Power Supply, Transformerless Power Supply, Fixed Voltage Power Supply, Voltage Inverter, Voltage Inverter II, Automatic Load Sensing Power Switch, 12V To 24V DC-DC Converter, Solid State Tesla Coil

Comments

Add A Comment

BillP
Voltage Inverter II
Saturday, October 10, 2009 2:24:12 AM
The original circuit appeared in the National Semiconductor Data Books as AN-69 (application note) in Dec. 1972. The circuit is correct as shown, however, the outputs as shown here are slightly different than in AN-69. AN-69 shows the 'positive' from the center (0) to the upper output as V+ with an arrow pointing upwards (from 0) to the upper output. It then shows the 'negative' from the lower output to center (0) as V- with an arrow pointing upwards (from lower) to the center (0).
innominata
Voltage Inverter II
Thursday, July 16, 2009 2:20:03 AM
to the previous poster : Imagine a 9v battery. It is connected to the ground of the 9v source. The outputs from this circuit are 4.5v, 0, -4.5v. The potential difference between 4.5 and -4.5 is 9, exactly the same as the battery. As long as you dont earth anything else to the 9v battery's -ve terminal believing its 0v, you will be fine (its actually -4.5v with reference to the 4.5v and 0v outputs). Voltage can be a tricky thing to get your head around. There is no such thing in a circuit run off a battery as 'earth'. Just a difference in voltage potential between the two terminals.
anonymous
Voltage Inverter II
Wednesday, June 03, 2009 8:02:31 AM
Have you ever considered the fact that it is physically impossible for it to work? Look at the -V/2 output, it's connected to the ground
abel gardener
10kva inverter circuit
Sunday, March 08, 2009 5:49:09 PM
you have been a great help to many peoples in career and more especially to me thanks for your good works
victor
POWER INVERTER BOARD
Wednesday, January 14, 2009 8:11:12 AM
This circuit can be used to power a small strobe or fluorescent lamp. It will generate over 400 VDC from a 12 VDC, 2.5 A power supply or an auto or marine battery. While size, weight, and efficiency are nothing to write home about - in fact, they are quite pitiful - all components are readily available (even from Radio Shack) and construction is very straightforward. No custom coils or transformers are required. If wired correctly, it will work. Output depends on input voltage. Adjust for your application. With the component values given, it will generate over 400 V from a 12 V supply and charge a 200 uF capacitor to 300 V in under 5 seconds. For your less intense applications, a fluorescent lamp can be powered directly from the secondary (without any other components). This works reasonably well with a F13-T5 or F15-T12 bulb (but don't expect super brightness). Q1 does get quite hot so use a good heat sink. C1 1 uF D2 1N4948 R2 +------||------+ T1 1.2KV PRV 1K 1W | | +-----|>|-----//---+------o + | R1 4.7K, 1W | red ||( blk | +-----//-----+------+ ||( | | yel )||( +_|_ C2 + o----------------------------------+ ||( --- 300 uF | red )||( - | 450 V | +--------------+ ||( | | Q1 | ||( blk | 6 to 12 | |/ C +--------------------+------o - VDC, 2A +----| 2N3055 Stancor P-6134 D1 _|_ | E 117 V Primary (blk-blk) 1N4007 /_ | 6.3 VCT Secondary (red-yel-red) | | - o------------+------+
Michael Oladipo
12V to 120V inverter
Monday, November 24, 2008 7:58:03 AM
the astable multivibrator is not working. It will be wise and more appropriate to use a driver/pre amplifier to drive the power transistor before feeding it to the transformer.
Ohztech
Voltage Inverter II
Thursday, April 10, 2008 1:06:51 AM
Hi! i find this design very usefull, thanks... i would like to know if there will be a change to increase the ouput voltage to at least ±12 to ±15 volts? What will be the new design?
Ralph Saliba
Microwave Oven Secondary Voltage Doubler
Sunday, February 10, 2008 3:41:43 AM
Can you be kind enough to furnish me with a circuit to double the Secondary output voltage of this transformer. I believe that the current in this respect is divided by 2. Regards Ralph
Haz
Voltage Inverter II
Saturday, December 15, 2007 8:22:35 AM
Hey! You couldn't possibly be able to tell me how many amps this can handle? I need it so i can create a phase shift oscillator for my op amp, that means i can make a near sine wave to power my inverter!
Paul
Voltage Inverter II
Wednesday, December 12, 2007 5:48:38 PM
Your site is fantastic I have viewed Your site please can you give me more explanation on the complete circuit of 5KVA inverter and 10KVA Inverter and there circuit board with the automatic changer thanks you
Gabriel
powersupply
Wednesday, August 29, 2007 5:42:04 AM
please i need a power supply with 12 v,24 ,16, 180v which can be regulated
anonymous
Voltage Inverter II
Monday, July 16, 2007 11:28:15 AM
Thanks for your site but how do I keep the cell from bein dead?
diego
5KVA to 10Kva inverter circuit board
Wednesday, June 20, 2007 8:55:10 AM
I write this mail in regards 5KVA to 10Kva inverter circuit board. I would like that you explain me the circuits if you can. regards diego
jon
24 secs shot clock
Thursday, June 14, 2007 12:47:18 AM
hi god day, please furnish me schematic diagram for 24 secs shot clock.. thank you very much..
Akinyele kayos
5KVA to 10Kva inverter circuit board
Monday, May 28, 2007 2:27:35 AM
yes ur site is fantastic and I have being viewing ur site so pls give more explanation on the complete circuit of 5KVA inverter and 10KVA Inverter and there circuit board with the automatic changer thanks you
Jim McGuire
Voltage Inverter II
Monday, April 02, 2007 8:38:42 AM
You'll probably find this circuit is no good for op amps -- unless you're intending to use it for input and not for gain -- since it can't deliver much more than 10mA
anonymous
Voltage Inverter II
Tuesday, March 20, 2007 10:49:03 PM
I would like to know what the inverter inverts
scotty243
Voltage Inverter II
Tuesday, March 20, 2007 9:53:01 PM
100-500W inverter... Hmm ("thinking abstractly") your better off using an oscillator amplifying the sinusoidal output to a reasonable voltage then running it through a step up transformer - use MOSFETs for the output of the amplifier. They don't run a risk of thermal runaway
wale taiwo
Voltage Inverter II
Friday, March 02, 2007 4:29:16 AM
pls the site is fantastic but can u pls send me inverter of about 100 -500w
All comments are being shown. Show Only Last 10 Comments. Add A Comment

Back To Circuits Page | Mail Me | Search | Buy Me A Coffee