Simple Two Speed Contactor DC Motor Controller


Home > Circuits > Other > Simple Two Speed Contactor DC Motor Controller Buy Me A Coffee
Author Views Views Today Rank Comments
208,138 13 21
The simplest of all motor controllers (besides a straight on/off switch) is the contactor controller. I designed this contactor controller for use in my electric scooter project. It is based around three 12V relays, two 12V batteries, two switches and of course a motor. Having no silicon to "fry", it is quite reliable and robust. A contactor controller works by rearranging the two (or more) supply batteries between series and parallel. This gives the motor a slow speed (batteries in parallel, current adds) and a fast speed (batteries in series, voltage adds). This assures that both batteries are discharged equally. When the circuit is "at rest", the batteries are connected in parallel, which allows easy recharging.

Schematic

This is the schematic of the contactor motor controller

Parts

Part
Total Qty.
Description
Substitutions
K1, K2, K3312V 30A SPDT Relay (See Notes)
S1, S22SPST Switch or Button
B1, B2212V Battery (See Notes)
M1112V or 24V Motor (See Notes)
MISC1Case, Wire, etc.

Notes

  1. S1 closes K3 and thus causes M1 to operate. S2 activates K1 and K2, reconfiguring the batteries for series operation and thus causes M1 to operate at "fast" speed.
  2. B1 and B2 should be chosen based on the current requirements of M1. Often, sealed lead-acid type batteries are available at local suppliers for surprisingly low prices. These batteries are ideal for things such as scooters, go-karts, etc.
  3. The relays are standard automotive type relays, available cheaply from any auto parts store.
  4. Your motor will depend on your requirements. 12V motors will normally run fine at 24V, and vice versa.
  5. You will notice that in series mode, all three relays only pull power from B2. This is because the relays have 12V coils, and it is impossible to switch the batteries from series to parallel and keep power to the coils at the same time. This does, however, mean that B2 is discharged slighty before B1. This should normally not be an issue unless the batteries are being drained completely "dead". Draining a battery dead is not good for it in any situation, and should be avoided. If you wish, you can use a small 12V battery to run the relays separately.
  6. You can add two more speeds to this controller using the schematic below. It connects at points A and B shown above on the controller schematic.

    Adding more speeds

    K1 is simply another of the same relay as used in the controller. S1 is another switch. R1 needs to be chosen based on your motor, but it will be of low value (under 10 Ohm) and high wattage (normally at least 100W). It must be capable of handling the full current drawn by the motor. This is not exactly an efficient way to limit current to the motor as excess current is dissipated as heat by the resistor, so it is normally only used for a "starter" speed.

Related Circuits

Air Flow Detector, Wire Loop Alarm, Simple Two Speed Contactor DC Motor Controller , 7 Segment LED Counter, Simple Lie Detector, Low Voltage Alarm, Video Stabilizer/MacroVision Removal, Pulse Width Modulation DC Motor Control, Simple Polarity Tester, Pine Racecar Victory Judge, Rain Detector, Time Delay Relay, Time Delay Relay II, Stepper Motor Controller, Touch Switch, Video Activated Relay, Digital Keypad Combination Lock, AC Motor Speed Controller, Simple Servo Controller, Water Detector With Sump/Bilge Pump Controller, Simple Touch Switch

Comments

Add A Comment

Ken B
Simple Two Speed Contactor DC Motor Controller
Sunday, December 12, 2010 11:01:21 AM
I want to use this to replace a fried 100 amp Curtis controller on a mobility cart that belongs to a relative. I know I'll have to use larger relays or parallel enough smaller one to handle the load. I've already ordered enough 60s to do that. I expect to fry the speed pot when I turn it on so: where would be the best place in the ckt to install the new one and what values should be used. Also: By adding the additional relay, will that increase or decrease the speed?
aaron
Simple Two Speed Contactor DC Motor Controller
Thursday, January 21, 2010 11:51:42 AM
what happens when both switches are on?
anonymous
Simple Two Speed Contactor DC Motor Controller
Monday, May 25, 2009 10:41:12 AM
My daughter had a 'new' but defective scooter given to her. The motor and batteries were fine, but the controller was shot. So I tried to make a simple go/no go controller for it. I had a LOT of relays salvaged from appliances, so getting enough of them was no problem. However, we soon learned that, while it DID work, sooner or later, usually sooner, the relay(s) would short closed. Even paralleling them, usually one or another would short closed, and we were right back to square one. This made the scooter want to run on despite the brake. (I kept that for obvious reasons, but it's rather wimpy) I knew that the relays I were using were rated for AC volts and amps, which I figured would be OK for DC as well, and, like you, I used one battery to run the relays, knowing that the drain was minimal. What I could not determine, at first, was the DC ratings for AC rated relays. I later learned that going from about 120 VAC to 12 VDC equaled about the same AMP rating as printed on the relay. Turns out this isn't enough, hence the fried relays, with stuck contacts. (Most of the relays I had on hand were in the range of 10 to 20 amps at best) The motor is already the right type, and the batteries were the ones that came with it, 12 V @ 7 AH or maybe it was 9 AH, I forget now. What I wanted to do, besides have BOTH 12 volt slow and 24 volt high speed, (I was having to change it manually) was to use regenerative braking, as the brakes on the thing were, as I said, wimpy at best, and we have hills which could be coasted down, extending the range. However, I am not an engineer, nor much of an electronics expert. This part, regenerative braking, was beyond me. I could not, and still do not, know of any simple way to accomplish this. I do know that the motor will act as a DC generator if turned, but how do I 'steer' the current the way I want, while NOT having the batteries trying to turn the motor themselves? This is the part that stumps me. I thought that, if the relays are closed, and the motor was turning fast enough to make MORE volts than the batteries were then at, it would automatically send the voltage the direction I wanted. Everything I have learned tells me that this should be so... Higher voltage to lower voltage, like hot to cold. (Higher energy to lower energy, in any form) Am I missing something simple here? I also plan to include a 'fail safe' in case of stuck relays in the future. We have had some close calls with a kid on a run-away scooter. I would like to use something that absolutely can not fail to disconnect the battery(s) from the motor in a hurry should that ever happen again. I plan to rebuild the relays and all using the plans you provided, using proper rated automotive relays this time, even though I still have dozens and dozens of appliance relays on hand. Any ideas on a truly fail safe way? I'm thinking of a gadget like they use on treadmills, so if you fall off, you pull out a tab that stops it, but it can't be a relay type like treadmills use. Maybe a heavy duty wire disconnect of some sort? Two copper contacts with a copper 'tab' that slides in between, making the motor wire whole, which would be attached to kid via string, and clipped to shirt. Pull out copper 'tab' and wire is 'broken' I can make that, although I know it will cause some loss and heating, I prefer that to a hurt kid. Any and all suggestions will be greatly appreciated, as are your two speed controller. And may I offer this: Treadmills have a tremendous motor in them! I have found them to be PM DC motors, and easily made into generators, (Exercise bike and gas engine driven) step-less speed controlled lathe motors, and more. The electronics in them for speed control is easily adapted. If only it was all designed for 12/24 volts I'd be all set. But it's designed for 120 VAC, and this is converted to 90 VDC and on down, using a pot. Using the motor without the control electronics, as a generator, I have found that, with a good quality (gym type) exercise bike, I can easily make 12/14 volts at 10 amps and more, and with a small gas engine, I could make about 100 volts DC, (That engine wasn't running too good at the time, and gearing wasn't perfect) at amperage of I don't know! I don't know because I couldn't load it down enough to make a good guess. A 100 watt incandescent light bulb plugged in made the engine slow down not at all. I had expected it to stall the little snowblower engine, which, as I say, wasn't running up to snuff, but it (the load) made NO difference at all. I suspect I could have plugged in about 500 watts of resistive load before it would have bogged down the poorly running engine. (A two stroke of aprox. 5 HP if running right) my calculations tell me that 5 HP ought to be able to make a whole lot more that that, but I don;t think the DC motor could. It is rated at 90 Volts DC at something like 10 amps? I do not remember right off the top of my head now. Might have been more. Anyways, I can see several possibilities with such motors. With the exercise bike, using a dryer drum belt on the bikes own wheel, (making the wheel not only a flywheel, as it was intended, but a pulley too) and a small pulley on the DC motor, I was easily able to light up a car sealed beam headlight, although I can't keep up that pace for very long. (I have a progressive form of MS. = Multiple Sclerosis) I calculated that when I had the car headlamp going good, I was only making about 55 watts. (I had meters inline for amps and voltage too) Now, If I could only find a way to use several of these treadmill motors together with a single 6.5 HP 4 cycle, OHV engine, which I happen to have on hand, so that I can make the most of the horsepower of that engine even at just a fast idle, I should be able to make some real back-up power. I should be able to recharge our backup batteries, all at once, and in that way, survive the next big storm. (I'm in the Midwest, Tornado alley) It happens that we end up without power for as much a a couple of weeks at a time, when it happens. I can't take that heat and humidity, it's real bad for people with MS. But with a couple or several deep cycle batteries, an old UPS as inverter, as well as a 'portable' inverter, and a efficient way to recharge, we would be able to make it OK next time. I nearly died last time it happened. I think I read that you work in the UPS business? What is your take on using them as inverters this way? I know I can't get more than about 700 watts out of mine, but I believe it's a much 'cleaner' sine wave form than the other inverter, which claims a "Modified Sine waveform" aka, a stepped square wave. I find that induction motors are picky about that. (Like fans, refrigerators, etc) Am I right, that a good, name brand UPS, which has 'cold start up' is the better for the job? (mine is an APC 700 'Smart UPS 700' which is good for about 700 watts, right?) We have used this setup for short outages, and it works, but we've never had to rely on it for more than a few hours so far. Using the car, or worse, my truck, to recharge batteries in an extended power outage is wasteful in the extreme. And you can't go get more gas... The gas station needs juice to run the pumps! (Plus the kids are too dumb to figure out how to make change without the cash register to tell them) I'd really like to have a decent system on hand, with out breaking my piggy bank. (Being 100% disabled, I'm on Social INsecurity, which doesn't pay real well, especially raising three daughters!) That's one reason I like to build and recycle as much (many) of the things I need as possible. (I also happen to just like tinkering around to stay busy, and doing for myself) Your thoughts? Comments? Was this way too long? (I know, Yes it was. I used to be a freelance reporter, paid by the column inch, so, knowing I'd be heavily edited, I just wrote more, and more! A habit I still can't break) Sincerely: Chris Mills aka The Junkman
anonymous
Simple Two Speed Contactor DC Motor Controller
Monday, February 02, 2009 8:23:00 AM
what was used before a simple two speed contactor dc cvontroller was implemented or made.I need this for a presentation of this circuit
anonymous
Simple Two Speed Contactor DC Motor Controller
Monday, June 02, 2008 3:14:56 PM
Links above DO NOT WORK! ASP error when code entered. site not user friendly. spam code overkill.

(Editor's notes: Thousands of comments are posted per day without issues. What was the ASP error? If you had mentioned the error, I would be able to troubleshoot and fix the issue...)

anonymous Tommi
Simple Two Speed Contactor DC Motor Controller
Sunday, October 14, 2007 8:13:27 PM
Thank you for your time in this presentation of a simple controller, greatly appriciated, will gather thses parts and test out.
rakesh r makwananymous
solution for make low watts in contorller in electric bike
Sunday, September 09, 2007 5:03:22 AM
hi , dear, i need solution for make out put watts low, can it posible in my recent controller of my electric bike ? my cotroller right now is 250w for use of 48 v battery. right now i need solution of want low output watts from controller with loading one person. i hope reply me promptly.
shittu oluwole johnson
Building of feedback motor
Saturday, August 04, 2007 3:53:15 PM
I've been trying for the past couples of days now to build a simple 12V DC motor using FDN and PFN circuit but is not working out because anytime i apply the power; it just scooting on without any control and if their is any barrier on the way it will be put to stop instead of getting power from the feedback circuit.Is their anything i could do to make it work properly.
bala_udhaya
Simple Two Speed Contactor DC Motor Controller
Sunday, July 29, 2007 1:36:08 AM
the cost of this circuit ?..
senthilkumar
dc motor used in bike(low volt high speed with high ampere
Friday, July 20, 2007 8:18:10 AM
hi, i need the details of the dc series motor used in motor bike (for electric bike).
cosmas c.
Simple Two Speed Contactor DC Motor Controller
Thursday, July 19, 2007 4:32:39 AM
can i get that of AC motors
Steve
Simple Two Speed Contactor DC Motor Controller
Sunday, July 15, 2007 12:40:54 AM
Two graduate projects and one project "to the faculty"...wow...is there a way to chip these people so they can be tracked? I don't want to buy anything from the companies they end up working for.
Firdausnonymous
DC motor speed control using PIC microcontroller
Wednesday, June 13, 2007 9:16:16 PM
Hello.. I need articles and circuit diagram with source code for "DC motor speed control using PIC microcontroller" for my graduate project.. I am waiting for your reply.. Thank you..
Nick
Simple Two Speed Contactor DC Motor Controller
Wednesday, June 13, 2007 8:07:03 AM
Can anyone show me how to make a one speed motor into a two speed motor? I have a 7.5 HP Pool pump but i need only half the amount of horse power. 7.5 is too much. It runs on 220 Volts. Thanks
Alan Jackson
Simple Two Speed Contactor DC Motor Controller
Tuesday, May 29, 2007 12:04:55 AM
I have been hunting for a controller circuit that I can build and this is it. I have a stern wheel paddle boat I built that runs on 12vdc and so far it has been running wide open both in forward and reverse. Obviuosly this is hard on the drive train. The second circuit is what I need as I run two seperate motors. (one for each side as the paddles are split for stearing purposes along with the rudder) They draw 8-12 amps under load so the 30 amp relays are plenty enough. I will let you know how it turns out.
yonis
Speed High DC Motor Controller with PIC MICROCONTROLLER
Thursday, May 24, 2007 4:27:34 AM
I NEED CIRCUIT DIGRAM WITH SOURCE CODE . PLEAS I NEED THEM FOR MY GRADUTE PROJECT. THANKS FOR YOUR HELP
anonymous my name is haliru umar from federal polytech birnin kebbi, kebbi state.
operatio of stepper motor controller
Friday, May 11, 2007 12:25:06 PM
hello sir i want to know the operation of stepper motor controller and how the stepper motor look like and also what is the function of each components that controlling the motor step by step thank you.
George Taylor
Simple Two Speed Contactor DC Motor Controller
Thursday, May 10, 2007 10:55:05 AM
Your design is flawed. 24VDC through two 30 amp 12 VDC relays placed in series is a bad recipe. On the bench it works but in practical use K-2 and/or K-3 burnout as soon as the circuit is put under load.

(Editor's notes: Well, I've been using this circuit nearly every day on my scooter for the past 5 years...)

Rahma
Simple Two Speed Contactor DC Motor Controller
Thursday, April 26, 2007 1:52:43 PM
Hello sir, I am a student at the 2nd year of the faculity of engineering "Mechatronics" department Please i need articles for "possition and speed control ofDC motor"for a project to my faculity. wait for your reply sooner thank you yours, Rahma
anonymous
Simple Two Speed Contactor DC Motor Controller
Monday, March 26, 2007 2:24:00 AM
hi all. My name is enkhee. I am mongolian. I want to do this kit. Then this schematic contact to AT89C51 microcontroller.
Jimmy E maasam
Simple Two Speed Contactor DC Motor Controller
Monday, March 12, 2007 9:23:49 AM
Yes am an Industrial electrical technician,i would like to congratulety all of you due to your work,thanks very much.my comments is that,can you help me to get the Simple two speed contactor AC motor controller.thanks very much. from TANZANIA
All comments are being shown. Show Only Last 10 Comments. Add A Comment

Back to Circuits Page | Mail Me | Search | Buy Me A Coffee